How Loud Should My Master Be? LUFS for Spotify, Apple Music and the Rest

By Dan Lopes Published

The short version

Master for the music, not for a number. Spotify turns every track toward -14 LUFS, the only target a major platform publishes, so a louder master doesn't play louder there. Keep true peaks below -1 dBTP and the meter out of the red.

Short answer: master for the music, not for a number. Spotify turns every track toward -14 LUFS integrated, the only loudness target a major platform publishes, so a louder master doesn’t play any louder there. Keep true peaks below -1 dBTP and the meter out of the red.

You’ve finished a mix, you’ve pushed it through a limiter, and now you’re wondering whether it’s loud enough to sit next to everything else on a playlist. Here’s what the platforms actually do with your master, which numbers are official and which are just repeated, and how to check yours.

What is LUFS?

LUFS (Loudness Units relative to Full Scale) is a measurement of how loud audio sounds to a listener, averaged over time. Unlike a peak meter, which only shows the highest point of the waveform, it weights the frequencies the ear is most sensitive to.

Two readings matter for a master:

  • Integrated loudness is the average across the whole track, in LUFS. It’s the number streaming platforms use.
  • True peak is the highest level the waveform reaches once it’s converted back to analog, in dBTP. It can land above the highest sample, which is why a file that never touches 0 dBFS can still distort after encoding.

What does Spotify do to a loud master?

Spotify turns it down. Every track is adjusted toward -14 LUFS integrated by default, so a master at -8 LUFS plays back about 6 dB quieter than it was made.

Quieter tracks are turned up, but only as far as their headroom allows, and Spotify applies a limiter to soft, dynamic tracks to make that possible.

Premium listeners can change the target in the app’s settings: Loud is -11 LUFS, Normal is -14 and Quiet is -19. Spotify says these apply to every format it streams, lossless included.

Spotify’s own recommendation for the master:

Spotify recommends
Integrated loudness-14 LUFS
True peak, master at or below -14 LUFSbelow -1 dBTP
True peak, master louder than -14 LUFSbelow -2 dBTP

The stricter ceiling for louder masters is there because lossy encoding adds peaks of its own, and a loud master has less room to absorb them.

What about Apple Music, YouTube, TIDAL and the rest?

None of them publishes a loudness target the way Spotify does. That’s worth knowing before you trust the “LUFS chart for every platform” that turns up in every search.

The figures that get repeated:

PlatformUsually quotedWhere the number comes from
Apple Music-16 LUFS (Sound Check)Blogs and plug-in makers. Apple’s own mastering guide doesn’t state it in the parts we read
YouTubeabout -14 LUFS, turned down onlyMeasurements by third parties
TIDAL-14 LUFS, normalized per albumThird-party reports and an audio research paper TIDAL worked with
Amazon Music-14 LUFSBlogs and plug-in makers
Deezer-15 LUFSA Deezer staff reply on its community forum, which says it may change

Checked 28 October 2026.

The useful takeaway is that they cluster between -14 and -16. A master that suits Spotify won’t be far from any of them.

Should you master to -14 LUFS?

No. Master for the music. Mix and master with your ears, not your eyes: the number tells you what Spotify will do to your track, not how it should sound.

The rule of thumb that matters more is an old one: don’t let the meter go into the red. Past a certain point, loudness stops helping and becomes destructive, and on Spotify a louder master is turned down to the same level as everyone else’s anyway.

Some genres push it on purpose. In phonk and many heavier styles, the distortion that comes from exaggerated loudness is part of the sound. That’s only a good reason when it’s part of the artistic vision. For almost everything else, keeping the meter out of the red still wins.

When normalization is off. Some listeners switch it off, and downloads, DJ sets and players outside streaming don’t apply it at all. Then nothing turns a loud master down, so it plays louder. Whether that’s worth it depends on the music, which is the same judgement as everywhere else in this piece.

An album is where a number earns its place. Across a release, every track has to sound like it comes from the same place. That’s when choosing one integrated loudness and mastering every track to it makes sense.

How do you measure your master’s loudness?

With your DAW’s own loudness meter: any decent DAW has one among its stock plugins. Look for one that reads integrated LUFS and true peak, and play the whole track through it from start to finish, since integrated loudness is an average and a 30-second loop will mislead you.

Then check the true peak reading against the table above, and leave a little more room if the master is loud. Use the meter to check, not to decide: your ears still make the call.

Do you need DistroKid’s Loudness Normalization extra?

Probably not. DistroKid sells an add-on called Loudness Normalization for $2.99 per track, one-time, which adjusts a track to Spotify’s recommendation: -14 LUFS integrated and a -1 dB true peak.

Spotify already does that on playback, and DistroKid’s own Extras window says that if your album is already above -14 LUFS, “this optimization will be skipped and you won’t be charged.” We cover it in more detail in our DistroKid pricing guide.

Key takeaways

  • Spotify is the only major platform that publishes a target: -14 LUFS integrated, true peak below -1 dBTP, or below -2 dBTP for a louder master.
  • A louder master is turned down on Spotify by default, so it ends up at the same level as everyone else’s.
  • The numbers quoted for Apple Music, YouTube, TIDAL, Amazon and Deezer are reported, not published, and they sit between -14 and -16.
  • Master for the music, by ear, and don’t let the meter go into the red. The number tells you what Spotify will do, not what your master should be.
  • Pushing loudness into distortion is only worth it when it’s part of the sound, as in phonk and some heavier styles.
  • For an album, pick one integrated loudness and master every track to it, so the release sounds like it comes from one place.

Our recommendation

Master by ear, keep the meter out of the red and true peaks below -1 dBTP. Check the integrated loudness with your DAW’s meter so you know what Spotify will do to the track, and if you’re releasing an album, choose one number and master every track to it.